Jump to content
Sign in to follow this  
blind_injustice

TTuned Horse Power Heroes!

Recommended Posts

TTuned Horsepower Heroes Leaderboard!

 

Rules: Must have Dyno Readout sheet posted.

Must have Spec posted as this.

Engine:

Turbo:

Mods:

Nos: Y/N

 

Have fun guys!

Share this post


Link to post
Share on other sites

Dean. | 1jzgte - Jzz30 | ct12a's TT | 160rwkws | Standard

 

Can't find dyno sheet atm, will look for it.

Share this post


Link to post
Share on other sites

Ryan | 1JZ-GTE with VVTi | GT3076R core in standard CT16b housings | 325rwhp | 16psi

 

dynokwnm.jpg

 

dynokwpsi.jpg

Share this post


Link to post
Share on other sites

well i was number 1 for all of about 2 hours :lol:

 

fkn crank that shit matt!!

 

Haha I saw it earlier and thought I'd let be No.1, just for a bit lol. Anyways it's gonna make way more once I put in my 1000cc, run a toluene mix and crank 1.5 bar into it...

Share this post


Link to post
Share on other sites

Aaron / 1jz / t70 / 231.1rwkw running 12psi have dyno sheet somewhere but that was long time ago.

 

been through a few turbo setups since then... aiming for the 500rwhp with 2j, 35r, 264 cams, emanage, 650cc sards etc etc... :)

Share this post


Link to post
Share on other sites

My soarer made 305rwkw on 17psi with the previous owner, MR 1JZ. SFA Timing, Safe tune and 6800rpm limiter to keep it alive.

 

We're Adding 1100cc injectors and a dual feed rail, HKS 272/9.3 cams and another 044 and tuning for 450rwkw/600rwhp on 98ron pump fuel.

 

 

| Ben | 2JZGTE | Trust T78-33D 17cm | 304.7rwkw/408.6RWHP | 17PSI

 

 

No dyno sheet by here is a video of the dyno run and the graph displayed.

 

Share this post


Link to post
Share on other sites

Update for my soarer. 177kws on 11psi, aftermarket exhaust. still have the twins.

dyno 177kws.jpg

Share this post


Link to post
Share on other sites

204.6kw - 1jz cressida. 3in exhaust (stock cat and dumps), cooler, 040, emanage, 17psi.

 

227977_10150176223482964_777167963_6746996_7641953_n.jpg

 

Punching cat and taking out a muffler and going for 220+

Share this post


Link to post
Share on other sites

Nghia-jzx100 1jz-gte vvti/hks 3037/sard 550cc/fuel pump/apexi pfc/16psi-385hp

5256721748_8016ba8e68_z.jpg

Share this post


Link to post
Share on other sites

supra. 2jzgte stock motor. fuel clutch exhaust gt42r single turbo bla bla bla

 

GetAttachment1-1.jpg

Share this post


Link to post
Share on other sites

^^ i would be running 20psi, then you will see it come alive.

 

It won't hold 18psi so there's no point pushing it any further. I've got a new turbo set up on order! Gtx35r/ 6boost/22psi etc. Check members rides :)

Share this post


Link to post
Share on other sites

^^ i would be running 20psi, then you will see it come alive.

 

It won't hold 18psi so there's no point pushing it any further. I've got a new turbo set up on order! Gtx35r/ 6boost/22psi etc. Check members rides :)

ahh, that sucks. new setup sounds brutal! i'm waiting on a borgwarner EFR7670 myself :D

Share this post


Link to post
Share on other sites

2jzgte twin high flow a80 286.8 rwkw 18psi 384.61rwhp 836nm

 

will be more after a new tune as its running rich on boost

Edited by FST 02J

Share this post


Link to post
Share on other sites

thinking of installing my twin plate and putting it back on the rolers to bet more power or just wind the boost up to where its tuned for :D

Share this post


Link to post
Share on other sites

André / 1jz / stock twin ct12a / 312rwhp / 15psi

 

20110817190857.jpg

 

THats a awesome outcome!! my steel wheel ct12's are good for 20psi or something, so hoping for 250rwkw

Share this post


Link to post
Share on other sites

JZX90 -

Standard exhaust, standard cooler, standard intake, standard boost... standard everything!

72719_444541536049_583686049_5893411_7428199_n.jpg

 

3" exhaust, de cat, 13psi of boost using ebc. Still standard cooler & intake

286530_10150245666056050_583686049_7953645_89513_o.jpg

 

Current set up -

twin steel wheel ct12s, twin dump pipes, 3" front pipe, front mount, walbro, hard intake with pod. Turbos good for 20psi+.

 

DYNO SHEET STILL TO COME!!

Edited by adavis59

Share this post


Link to post
Share on other sites

Dean Newcombe and Daniel Prior should post up their figures. Both well over 300KW

Share this post


Link to post
Share on other sites

Here you go pman! Didn't realise this was here...

 

I can't seem to find the actual dyno sheet but I'll put it up when I do. This is a comparison chart I made from the data on the sheets.

 

Engine: 1.5JZ (2JZ-GE bottom end)

Turbo: Garrett GT3082R 0.82 exhaust housing - 19psi

Mods: Standard head and block, china exhaust manifold, china bar/plate front mount, 3" exhaust, 540cc injectors, Microtech LTX12, Bosch coils, MSD leads, OS Giken twin plate, upgraded R154

 

302kw/405hp - 938NM torque

 

dynopower.jpg

 

Share this post


Link to post
Share on other sites

Std internal SR20det, TD06 20g, cams, 1000cc inj, usual bolt ons.

260rwkw 18psi

CEFABEF5-885B-45B5-A0EB-F277B3777403-19980-0000056877A64E9B-1.jpg

D9C28CC6-A718-4C71-BC83-79199168EFFE-27431-00000778946E033C.jpg

Edited by greens14

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

×